Lawn Mower

Snapper Lawn Mower Parts: A Buyer’s Guide to the 5 Best Replacements

Your Snapper mower quit mid-stripe. Again. The grass is half-cut, the engine is fine, but a $20 part just sidelined a $400 machine. You need the right replacement, not a guess.

A good part matches your deck size, bolt pattern, and part number exactly. Cheap metal bends. Wrong wheels slip. The best replacements use hardened steel, correct tooth counts, and OEM-compatible numbering so you order once and get back to work.

We picked five parts that cover the most common Snapper failures: an air lift kit, a pair of drive wheels, a 21-inch blade, a mulching blade, and a set of 8-inch wheels. Each one fits a different machine and a different owner. Here is who should buy which.

Compare the key specs side by side before you scroll.

Features BERPSE Air Lift Kit ZALANA Front Drive Wheels KOLTRUNEX Mower Blade 8TEN LawnRAZOR Blade Shiosheng 8-inch Wheels
Part Type Air lift kit Drive wheels (pair) Walk-behind blade Mulching blade Wheel assembly (pair)
Key Spec Fits 28 and 33 inch decks 8 inch, 53 teeth 21 inch, bow-tie hole 20.6875 inch, mulch ninja 8 inch diameter
Material Steel with hardware High-quality rubber Heat-treated steel Hardened steel Rugged composite
Main Benefit Stops chute clogs Restores traction Clean cut, less clumping Fine mulching Quick bolt-on fit
Best Use Case Bagging decks Self-propelled mowers 21 inch walk-behinds Snapper 21500 series Brute, Craftsman, MTD
snapper lawn mower parts

BERPSE Air Lift Kit

1st Pick

BERPSE

335-422 7037723BMYP Air Lift Kit for Sna-pper 28" and 33" blades | Replaces 3-7723, 60480, 7037723, 7060480, 7060480SM

  • Part Number: 3-7723, 60480, 7037723, 7037723BMYP, 7060480, 7060480SM, 2126868; 50127
  • Includes hardware: Length4"; Outer Hole 5/16"; Thickness 0.134"; Width 3 5/8"
  • Air Lift Kit For Sna-pper 28" and 33" blades; Note!!! Does not fit 30-inch 2-hole

This kit is for the owner whose Snapper keeps clogging the discharge chute. If you run a 28-inch or 33-inch deck and spend half your mow stopping to clear wet grass, this is the part that fixes it. It bolts onto the blade spindle and throws air upward to keep clippings moving.

The kit includes mounting hardware, which saves a trip to the hardware store. Dimensions are specific: 4 inches long, 5/16-inch outer hole, 0.134-inch thickness, and 3 5/8-inch width. That matches the OEM numbers 3-7723, 60480, 7037723, and several others, so cross-referencing your old part is straightforward. Users report the chute stays clear even in damp conditions.

One catch: it does not fit 30-inch two-hole decks. Measure your deck before ordering. Also, the hardware is basic grade steel, so if you mow rocky ground, check the bolts after the first few cuts. It is not a heavy-duty commercial part, but for a residential Snapper it holds up fine.

  • Fits 28-inch and 33-inch Snapper decks only
  • Replaces OEM numbers 3-7723, 60480, 7037723, 7037723BMYP, and more
  • Hardware included: 4-inch length, 5/16-inch outer hole
  • Prevents grass from sticking in the discharge chute
  • Not compatible with 30-inch two-hole decks

Best for: Snapper owners with 28 or 33 inch decks who are tired of clearing clogs every few passes.

ZALANA Front Drive Wheels

2nd Pick

ZALANA

Set of 2 Front Drive Wheels Fit for Troy Bilt Lawn Mowers - Replaces 734-04018C 734-04018A 734-04018B, Drive Wheels for MTD Snapper Troy Bilt Tuff-Cut 210 TB210 TB230 TB240 Self Propelled Mower

  • 【COMPATIBLE】Fits Troy-Bilt TB210, TB230, TB240, TB250, TB270ES, Tuff-Cut 210, 12A-264U011, 12A-264V211, 12A-266A766, 12A-446A011,…
  • 【REPLACES PART NUMBER】Replaces MTD/Troy Built: 734-04018, 734-04018A, 734-04018B, 734-04018C, 12AV569Q597
  • 【HIGH-QUALITY】The front drive wheels are made of high-quality Rubber, Design with 53 teeth, provide enough traction to your lawnmo…

Self-propelled mowers lose traction when the drive wheels wear smooth. If your Troy-Bilt or Snapper TB210, TB230, or TB240 starts slipping on slight inclines, these ZALANA wheels are the fix. The set of two replaces part numbers 734-04018, 734-04018A, 734-04018B, and 734-04018C.

Each wheel is 8 inches in diameter with a 2-1/8-inch width and a 53-tooth drive gear. That tooth count matters because it engages the transmission pinion directly. Get it wrong and the mower will not pull. The rubber compound grips well on fescue and bluegrass, and installation takes about ten minutes with a socket set. You remove the hex nut, slide the old wheel off, and the new one slips on.

These are aftermarket, not OEM. The rubber is slightly harder than factory Snapper wheels, which means longer wear but a touch less cushion on bumpy turf. If your lawn is mostly flat, you will not notice. The six-month warranty covers defects, though normal wear is on you.

  • Fits Troy-Bilt TB210, TB230, TB240, TB250, TB270ES and Tuff-Cut 210
  • 53-tooth drive gear for positive transmission engagement
  • 8-inch diameter, 2-1/8-inch width, 1/2-inch bore
  • Replaces 734-04018, 734-04018A, 734-04018B, 734-04018C
  • Six-month warranty against manufacturing defects

Best for: Owners of self-propelled Troy-Bilt or Snapper mowers whose drive wheels have gone bald and slip on hills.

KOLTRUNEX Mower Blades

A dull blade tears grass instead of cutting it. That leaves brown tips and invites disease. The KOLTRUNEX 703371 blade is a direct replacement for Snapper 21-inch walk-behind decks, including SP60 through SP105 series and models like 1696607 and 7800923.

What sets this blade apart is the heat-treated steel. It resists bending when you hit a rock or a buried root. The black powder coating fights corrosion, which matters if you store your mower outside or mow damp grass. The high-lift airfoil pulls clippings up and out, so bagging works better and clumping drops. The bow-tie center hole is specific to Snapper spindles, so check yours before ordering.

The coating does wear off with use. That is normal and does not affect cutting. Also, this is a single blade, not a set. If your deck uses two blades, order two. The 0.138-inch thickness is standard for residential mowers, so it is not a commercial-grade slab of steel, but it holds an edge through a full season for most homeowners.

  • Fits Snapper 21-inch walk-behind decks, SP60 to SP105 series
  • Replaces OEM part 703371
  • Heat-treated steel with black powder coating
  • 21-inch length, 2.25-inch width, 0.138-inch thickness
  • Bow-tie center hole specific to Snapper spindles

Best for: Homeowners with a 21-inch Snapper walk-behind who want a durable replacement blade that bags and mulches well.

8TEN LawnRAZOR Blade

4th Pick

8TEN

8TEN LawnRAZOR Blade for Snapper C21409R C21509R C21559BV CP21409R CP21509R Walk Behind 7026407AYP (Mulching)

  • Compatible with OEM Parts Jonsered/Poulan/Snapper/Murray/Simplicity 7026407AYP
  • Compatible with Snapper 21500, 21500T2 , 21501, 215012, 215014, 215015, 216015, 216515BV , 2167519BFC, 2167520B, 2167520BFC, 21702…
  • Compatible with Snapper C21409R, C21509R, C21559BV, CP21409R, CP21509R, CP21559BV, A21509B, AP21509B, CAP21509R, CP215519HV, CP215…

Mulching fans, this one is for you. The 8TEN LawnRAZOR is a mulch-specific blade for Snapper 21500 series mowers, including C21409R, C21509R, C21559BV, and CP21409R. It replaces OEM 7026407AYP, which cross-references to Jonsered, Poulan, Murray, and Simplicity decks too.

The blade measures 20 11/16 inches long, 2 15/16 inches wide, and 0.138 inches thick. The center hole is 3/8 inch. The Mulch Ninja design recirculates clippings back into the turf, chopping them fine enough to break down quickly. That means less bagging and better soil nutrition. The steel is hardened, so it holds an edge longer than budget blades.

One limitation: this blade is optimized for mulching, not bagging. If you bag most of the time, a high-lift blade like the KOLTRUNEX above will move clippings better. Also, the 3/8-inch center hole is smaller than some Snapper spindles, so verify your bolt size. The 20.6875-inch length is slightly shorter than a full 21-inch blade, which is normal for mulch designs.

  • Fits Snapper 21500, 21501, 216015, 217020B, and similar models
  • Replaces OEM 7026407AYP
  • Mulch Ninja design for fine clipping recirculation
  • 20.6875-inch length, 2.913-inch width, 0.138-inch thickness
  • 3/8-inch center hole circle

Best for: Snapper 21500 series owners who mulch their clippings and want a blade built for that job.

Shiosheng 8-inch Wheels

Broken wheel on a push mower? The Shiosheng set of two 8-inch wheels replaces part 634-05040 and fits a long list of Brute, Craftsman, Yard Machine, and Snapper MTD models. If your mower has a cracked rim or a wheel that wobbles, this is a direct bolt-on fix.

Installation needs only a flathead screwdriver and a 9/16-inch socket. No drilling, no adapters. The 8-inch diameter matches the original, so your cutting height stays the same. The composite material handles typical lawn abuse and resists UV cracking better than some OEM plastic wheels. Two wheels come in the pack, which covers both sides of a push mower.

These are not drive wheels. They have no gear teeth, so they will not work on self-propelled models. Also, the hub offset and bore are not listed, so measure your axle before ordering. For a standard push mower, though, they drop right on. The price per pair is low enough that keeping a spare set in the garage makes sense.

  • Replaces part 634-05040
  • Fits Brute, Craftsman, Yard Machine, Snapper MTD models
  • 8-inch diameter, set of two wheels
  • Installs with flathead screwdriver and 9/16-inch socket
  • Not for self-propelled mowers (no drive gear)

Best for: Push mower owners with cracked or worn 8-inch wheels who want a cheap, quick replacement.

How We Chose These Products

We started with the most common failure points on Snapper mowers: clogged chutes, worn drive wheels, dull blades, and cracked wheels. Then we matched each part to its OEM numbers and verified compatibility with specific Snapper and MTD model lists. Parts that did not list clear cross-reference numbers got skipped.

We also weighed material quality against price. Heat-treated steel and rubber with a 53-tooth gear beat generic plastic. And we looked for parts that included hardware or needed no special tools, because a $15 part that needs a $40 tool is not a bargain. Every pick here fits a real machine and solves a real problem.

Buying Guide: What Really Matters

Part numbers are your best friend. Snapper uses numbers like 703371 or 734-04018C, and aftermarket sellers cross-reference them. Write down your model number and the old part number before you search. A blade with the wrong center hole will not mount, no matter how close the length is.

Material matters more than brand. Heat-treated steel blades hold an edge longer. Rubber drive wheels with the correct tooth count pull better than hard plastic. Powder coating fights rust. These details separate a part that lasts three seasons from one that lasts three mows.

Check the fit notes. Decks come in 28, 30, and 33 inches. Spindles use bow-tie or round holes. Axles have different bores. A part that fits a 33-inch deck will not fit a 30-inch. Read the compatibility list and measure twice.

Our Top Recommendation

The BERPSE Air Lift Kit is our top pick because it solves the most annoying Snapper problem: clogged chutes. It fits two common deck sizes, includes hardware, and costs less than a dealership service call. If you bag grass and fight clogs, start here.

For drive wheel issues, the ZALANA set is the runner-up. It restores traction on self-propelled mowers for a fraction of OEM cost. And if you just need a sharp blade, the KOLTRUNEX 703371 is the best all-around choice for 21-inch decks. Mulching fans should grab the 8TEN LawnRAZOR.

Frequently Asked Questions

How do I find my Snapper mower’s part number?

Check the old part first. Blades and wheels usually have a stamped number. If it is worn off, look up your mower’s model and serial number on the Snapper website or a parts diagram site. The model number is usually under the seat or on the rear deck.

Can I use aftermarket parts on a Snapper mower?

Yes, as long as the part number cross-references correctly. Aftermarket parts often cost less and work fine. Just verify the dimensions and hole patterns match. The parts in this guide list their OEM replacements.

How often should I replace my mower blade?

Sharpen a blade every 20 to 25 hours of mowing. Replace it when it gets nicked, bent, or too thin to sharpen safely. A bent blade causes vibration and can damage the spindle. If you hit a rock, inspect the blade before your next mow.

Will these wheels fit my self-propelled mower?

The Shiosheng 8-inch wheels are for push mowers only. They have no drive gear. For self-propelled models, use the ZALANA drive wheels, which have a 53-tooth gear. Check your mower type before ordering.

Affiliate Disclosure: We may earn a commission when you buy through links on this site, at no extra cost to you. This helps us keep testing products independently.

Jillur

Written by Jillur

Part of the Gardening Pleasure team, testing garden tools, lawn mowers and outdoor gear for real gardens.

Related posts